新聞中心
線性滑軌和直線導軌是怎么組裝的
來源:http://www.feicui77.cn/ 日期:2019-04-26 發布人:
線性滑軌一般在出廠前都加注了潤滑油,安裝在設備上后再加注潤滑油,切莫不可在導軌滑塊無潤滑的狀態下試運行操作。
Linear slides are usually filled with lubricating oil before they leave the factory. After installing on the equipment, they are added with lubricating oil. It is absolutely necessary to test-run the slider without lubrication.
直線導軌端部以及側面均有塑料零部件,安裝時切記不要用硬的工具錘擊,在安裝后進行試運行時,不要讓任何物件超速時對其碰撞,以免導致機械故障影響不良反應。
There are plastic parts at the end and side of the linear guide. When installing, don't hammer with hard tools. When running after installation, don't let any objects collide with them when exceeding speed, so as to avoid adverse reactions caused by mechanical failure.
線性滑軌主要是用在精度要求比較高的機械結構上和自動化機械上,線性滑軌屬于高質量,高精度,設計的產品,但在使用時也難免會出現故障,為了減少故障,保證的使用,組裝過程中要注意以下事項:
Linear slideway is mainly used in mechanical structure and automation machinery with high precision requirements. Linear slideway belongs to high quality, high precision and safe design products. But when it is used, it will inevitably fail. In order to reduce the failures and ensure safe use, the following points should be paid attention to in the assembly process:
1、標準端蓋是用塑料制成的。如用力敲打或碰撞,就會使其受損,故要加以注意。
1. Standard end caps are made of plastic. If hit or collide hard, it will be damaged, so we should pay attention to it.
2、如擅自拆卸各部位,就會導致粉塵的進入或使各部位組合精度的下降,為此,如不是萬不得已的情況,請不要輕易拆卸。


2. If the parts are disassembled without authorization, the dust will enter or the precision of the parts will decrease. For this reason, if it is not a last resort, please do not disassemble easily.
3、有時只需傾斜導軌,滑塊就會移動,所以這時應注意不要使滑塊從導軌上脫落下來。
3. Sometimes only tilt the guide rail, the slider will move, so we should pay attention not to make the slider fall off the guide rail.
4、互換性產品(即導軌和滑塊可以任意匹配的產品)的滑塊是以裝在暫用軸上的形式提供的。為此,在與線性滑軌相組合時,請加以留意。
4. The sliders of interchangeable products (i.e. products with arbitrary matching slides and guideways) are provided in the form of temporary axles. Therefore, when combined with linear slides, please pay attention to it.
- 上一篇:直線導軌絲杠的性能特點
- 下一篇:直線導軌是怎么防塵的
相關新聞 /RELATED TO RECOMMEND
導軌絲杠裝配避坑!全流程實操詳解,80%的故障源于裝配不規范,一次達標不返工
2026-04-13
導軌絲杠 | 滾珠絲杠避坑指南!原理吃透不踩雷,高精度傳動99%的人都沒搞懂核心邏輯
2026-04-08
導軌絲杠選型避坑!四步法精準選型,90%工程師都在用,杜絕動力不足、共振隱患
2026-04-07
別再瞎選導軌絲杠!垂直安裝不設防墜,幾千斤負載直接砸穿設備
2026-04-06
滾動 vs 滑動:導軌絲杠選錯,磨損翻倍、維護成本直接飆升
2026-03-27
導軌絲杠:人形機器人直線運動核心,一步穩不穩全看它
2026-03-26
拒絕卡頓、損耗!導軌絲杠,決定設備精度與壽命的核心關鍵
2026-03-26
導軌絲杠:被德日卡脖子半世紀,國產終于打破高精度壟斷
2026-03-25
導軌絲杠:機床精度的核心內功,制造破局不靠低價靠硬功
2026-03-24
直線模組選型難?吃透導軌絲杠這篇就夠了
2026-03-24
導軌絲杠卡死、精度下降?避開這些坑,少走半年彎路
2026-03-23
一文讀懂《傳動技術基礎(滾珠絲杠)》:滾珠絲杠的結構+精度+選型
2026-03-19





