新聞中心
滾珠絲杠在安裝時如何操作的?
來源:http://www.feicui77.cn/ 日期:2020-07-08 發布人:
1、滾珠絲杠屬于精密傳動裝置,必須進行潤滑。在螺母內使用家皂基潤滑脂1-3號透平油潤滑。山東博特精工股份有限公司網站|滾珠絲杠|直線導軌|主軸 1.滾珠絲杠屬于精密傳動裝置,必須進行潤滑。在螺母內使用家皂基潤滑脂1-3號透平油潤滑。
1. Ball screw belongs to the precision transmission device and must be lubricated. It is recommended to use soap base grease No. 1-3 turbine oil for lubrication in nuts. The official website of Shandong Bote Precision Industry Co., Ltd. ball screw linear guide shaft 1. Ball screw belongs to precision transmission device, which must be lubricated. It is recommended to use soap base grease No. 1-3 turbine oil for lubrication in nuts.
2.滾珠絲杠與滾動軸承一樣,混入灰塵異物將會降低使用壽命。因此,必須采用絲杠保護套加以保護。國內外各種類型的滾珠絲杠副大部分均已安裝有迷宮式密封環,防止贓物進入滾珠絲杠體內。另外,在金屬屑易侵入絲杠的場合使用時,還應考慮在絲杠全長上采用絲杠保護套防護。
2. Like rolling bearing, ball screw mixed with dust and foreign matters will reduce its service life. Therefore, it is necessary to use the lead screw protective sleeve to protect it. Most of the ball screw pairs at home and abroad have been installed with labyrinth seal ring to prevent dirt from entering the ball screw. In addition, when the metal chips are easy to invade the lead screw, the screw protective sleeve should be used in the full length of the lead screw.

3.由于滾珠絲杠螺母的特殊結構,不宜承受徑向負荷,以免造成絲杠彎曲,影響傳動精度和運動的靈活性,降低使用壽命。故安裝時,尤其要注意絲杠的軸心線與螺母座移動軌跡的平行,并使絲杠支撐軸線與螺母座軸線一致。
3. Due to the special structure of the ball screw nut, it is not suitable to bear radial load, so as to avoid the screw bending, affecting the transmission accuracy and movement flexibility, and reducing the service life. Therefore, during installation, special attention should be paid to the parallelism of the axis line of the lead screw and the movement track of the nut seat, and make the central axis of the screw support consistent with the central axis of the nut seat.
4.將絲杠安裝于設備上,注意不能使絲杠與螺母分離,以免滾珠脫出。安裝時不要敲打滾珠絲杠副,尤其注意保護滾珠導管,因其管壁教薄,碰撞變形將使鋼球流動受制約。
4. Install the lead screw on the equipment. Pay attention not to separate the screw from the nut, so as to prevent the ball from falling out. When installing, do not knock the ball screw pair, pay special attention to protect the ball guide tube, because the tube wall is thin, collision deformation will restrict the flow of steel ball.
以上就是導軌絲杠為大家介紹關于滾珠絲杠的相關內容,希望能夠幫助到大家。如需了解更多相關資訊,請繼續關注我們網站http://www.feicui77.cn 后續將呈現更多精彩的內容
The above is the guide screw for you about the ball screw related content, I hope to help you. For more information, please stay tuned to our website http://www.feicui77.cn More wonderful content will be presented later
- 上一篇:直線導軌的產品特點是什么?
- 下一篇:直線導軌安裝需要注意的幾點!
相關新聞 /RELATED TO RECOMMEND
滾珠絲桿裝配錯1步=精度報廢,導軌絲杠精密裝配全流程,零間隙實操指南
2026-04-27
導軌絲杠:精密傳動界的扛把子,聊聊滾珠絲桿的那些事
2026-04-24
導軌絲杠:滾珠絲杠副冷卻結構設計及溫升影響分析
2026-04-22
導軌絲杠選型避坑,梯形VS滾珠絲桿核心區別,90%從業者都選錯
2026-04-20
導軌絲杠裝配避坑!全流程實操詳解,80%的故障源于裝配不規范,一次達標不返工
2026-04-13
導軌絲杠 | 滾珠絲杠避坑指南!原理吃透不踩雷,高精度傳動99%的人都沒搞懂核心邏輯
2026-04-08
導軌絲杠選型避坑!四步法精準選型,90%工程師都在用,杜絕動力不足、共振隱患
2026-04-07
別再瞎選導軌絲杠!垂直安裝不設防墜,幾千斤負載直接砸穿設備
2026-04-06
滾動 vs 滑動:導軌絲杠選錯,磨損翻倍、維護成本直接飆升
2026-03-27
導軌絲杠:人形機器人直線運動核心,一步穩不穩全看它
2026-03-26
拒絕卡頓、損耗!導軌絲杠,決定設備精度與壽命的核心關鍵
2026-03-26
導軌絲杠:被德日卡脖子半世紀,國產終于打破高精度壟斷
2026-03-25




